benyaki Posted September 17, 2016 Share Posted September 17, 2016 I recently upgraded (finally) from 5.0 to 6.2. Before upgrading, I had no issues aside from some plugins starting to fail with no support. On first boot (with nothing installed, no plugins, no dockers, no VMs) I noticed that it was slow. I thought it might just be slow to start. It did not get better. Clicking on a tab or stopping or starting the array, anything within the webGUI is extremely slow, as in it takes approximately 2-3 minutes before the page refreshes, at minimum. (I just waited about 15 minutes to stop the array) newperms has been run just to be sure Downloading through plugins or downloading a docker is quick. Plugins work quickly. No problem streaming anything from the array on the plex docker. Since initial install, I have installed some plugins, a docker, and changed from a single cache drive to a pool (which is another two problems) but nothing has changed for better or worse. Attached is diagnostics Hardware is: Model: N/A M/B: Supermicro - H8DM8-2 CPU: @ 1800 HVM: Enabled IOMMU: Disabled Cache: 768 kB, 3072 kB, 6144 kB Memory: 0 GB (max. installable capacity GB) Network: eth0: 1000 Mb/s, full duplex, mtu 1500 Kernel: Linux 4.4.19-unRAID x86_64 OpenSSL: 1.0.2h Note - the motherboard did initially have an IPMI board installed (and has a second ethernet port for this) however there is no cable attached and I have since removed it from the motherboard and (I think) disabled it in the bios - not very straightforward tower-diagnostics-20160917-1330.zip Quote Link to comment
benyaki Posted September 17, 2016 Author Share Posted September 17, 2016 More hardware info attached (via lshw) hardware.txt Quote Link to comment
NotYetRated Posted September 17, 2016 Share Posted September 17, 2016 I had this issue and found that removing a couple of plugins which i did not really use anyways alleviated the issue i was having. I am racking my brain to recall which plugins i removed.... IPMI.... and 1 other. If it comes to mind, i will post back here. Quote Link to comment
benyaki Posted September 17, 2016 Author Share Posted September 17, 2016 I had this issue and found that removing a couple of plugins which i did not really use anyways alleviated the issue i was having. I am racking my brain to recall which plugins i removed.... IPMI.... and 1 other. If it comes to mind, i will post back here. The thing is that it was like this from the start, new install, without anything else (plg, docker, etc) added Quote Link to comment
benyaki Posted September 18, 2016 Author Share Posted September 18, 2016 Not sure exactly what the problem is/was, but I tried replacing bz files on the flash drive with a fresh download of 6.2, thinking something may be corrupt. It did nothing. I downloaded and replaced them with 6.19 version. The GUI is back to normal. It lost my docker for plex for some reason, just added it again and is working fine. Just need to replace some plugins that this broke, but I think all my issues should be solved now, fingers cross, knock of wood, etc. Quote Link to comment
benyaki Posted February 7, 2017 Author Share Posted February 7, 2017 This appears to still be a problem. I just upgraded to 6.30 hoping that something would have been solved, but i am having very slow webGUI response times. Dockers: Plex Sabnzbd duckdns Plugins (all updated): CA autoupdate CA Backup CA Cleanup Community Applications Couchpotato Dynamix Active Streams Dynamix sys info Dynamix sys temp Fix Common Problems (currently running extended test to see if anything comes up) Nerdtools Sickbeard Statistics Hardware: M/B: Supermicro - H8DM8-2 CPU: 2419 - 6 core @ 1800 HVM: Enabled IOMMU: Disabled Cache: 768 kB, 3072 kB, 6144 kB Memory: 0 GB (max. installable capacity GB) - not sure why it has this. There is 8GB installed right now. Network: eth0: 1000 Mb/s, full duplex, mtu 1500 tower-diagnostics-20170206-1848.zip Quote Link to comment
benyaki Posted February 7, 2017 Author Share Posted February 7, 2017 Solved. Was looking through syslog, found a bunch of avahi errors, thought I would solve that problem, apparently that was THE problem. somehow didnt show up during my forum search. hope this helps someone down the line. https://lime-technology.com/forum/index.php?topic=48508.msg515980#msg515980 Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.