saarg Posted September 28, 2017 Share Posted September 28, 2017 1 hour ago, ProGEEK said: They probably won't, since it's not required for anything relating to unRAID. As far as I know, it's only used by media modules As long as it's in the kernel source and doesn't add much in size they usually add stuff. It for sure doesn't hurt to ask Link to comment
DMcK Posted September 28, 2017 Share Posted September 28, 2017 Uploaded a new LibreELEC build with bzimage, if someone can confirm it works, we should be good. Tried that new version with my 950q and it didn't work for me. On my first reboot, I had the tuner plugged into the same bus that my flash drive is plugged into and unRaid was almost unusable. It took forever to get the GUI up. Rebooted with the tuner in a different USB port but the tuner still wasn't recognized. I ran out of time last night and had to get a working system back up, so I didn't investigate further. Link to comment
CHBMB Posted September 28, 2017 Share Posted September 28, 2017 2 hours ago, DMcK said: Tried that new version with my 950q and it didn't work for me. On my first reboot, I had the tuner plugged into the same bus that my flash drive is plugged into and unRaid was almost unusable. It took forever to get the GUI up. Rebooted with the tuner in a different USB port but the tuner still wasn't recognized. I ran out of time last night and had to get a working system back up, so I didn't investigate further. Yeah, that is going to need some looking at, reading about the 950q it has all it's drivers included in the kernel, so shouldn't present a problem, and not sure why you're getting issues. Link to comment
CHBMB Posted September 28, 2017 Share Posted September 28, 2017 (edited) sed -i -e 's/CONFIG_FRAME_VECTOR=y/CONFIG_FRAME_VECTOR=m/g' $D/kernel/.config Would probably be the easiest way to achieve things is my guess. I can chat to LT about it, but this would be easy to implement. I'll run another build tonight which should then "modularise" things and see what happens if @ProGEEK can test Edited September 28, 2017 by CHBMB Link to comment
CHBMB Posted September 28, 2017 Share Posted September 28, 2017 (edited) OK, here's another test release for Hauppage.... bzimage, bzroot and bzroot-gui are the same as stock, bzmodules and bzfirmware I hope will work with the Hauppage cards https://mirror.linuxserver.io/unraid-dvb-rc/6-4-0-rc9f/rc9f-libreelec.zip Edited September 28, 2017 by CHBMB Link to comment
ProGEEK Posted September 28, 2017 Share Posted September 28, 2017 3 hours ago, CHBMB said: sed -i -e 's/CONFIG_FRAME_VECTOR=y/CONFIG_FRAME_VECTOR=m/g' $D/kernel/.config Would probably be the easiest way to achieve things is my guess. I can chat to LT about it, but this would be easy to implement. I'll run another build tonight which should then "modularise" things and see what happens if @ProGEEK can test @CHBMB That latest version doesnt work for me. You'll still need to update mm/Kconfig to allow frame_vector to be compiled as a module. as the Kconfig file defines that the frame_vector component is a boolean (See my patch) Attached is the patch for just modifying mm/Kconfig enable_module_building_frame_vector.patch Link to comment
timl Posted October 3, 2017 Share Posted October 3, 2017 I am trying to read through this post and figure out exactly what I need to do, but I am a little lost I am brand new to UnRaid and trying to get a Hauppage WinTV DualHD working through to a docker container. I installed this plugin, choose LibreElec 6.3.5, rebooted, and it still doesnt seem to be recognized. Is there more to this I need to do? It shows the DVB kernel was detected but no adapters. I am sure the card is good as I was using it in another system earlier today. lsusb shows the device as being there as well. Link to comment
DMcK Posted October 3, 2017 Share Posted October 3, 2017 You probably missed the part in the first post on adding --device=/dev/dvb/ to the Extra Parameters section of the TV docker you are using. Link to comment
timl Posted October 3, 2017 Share Posted October 3, 2017 Thanks for the reply DMcK. I did catch that part but have not tried that. On the status page for UnRaid DVB it doesnt show the adapter as being detected, so /dev/dvb isnt being created. Link to comment
CHBMB Posted October 3, 2017 Share Posted October 3, 2017 18 hours ago, timl said: I am trying to read through this post and figure out exactly what I need to do, but I am a little lost I am brand new to UnRaid and trying to get a Hauppage WinTV DualHD working through to a docker container. I installed this plugin, choose LibreElec 6.3.5, rebooted, and it still doesnt seem to be recognized. Is there more to this I need to do? It shows the DVB kernel was detected but no adapters. I am sure the card is good as I was using it in another system earlier today. lsusb shows the device as being there as well. There are two versions of this tuner. v6.3.5 is on kernel version 4.9.30 Need to know what version you have so which one of these commands gives you the relevant information about your tuner? lsusb -v -d 2040:026d lsusb -v -d 2040:0265 You may find you have more luck with the RC9f release of Unraid as it's a later kernel version. With the release of v6.4 I'm probably not going to backport support of v6.3.5 stuff. Link to comment
timl Posted October 4, 2017 Share Posted October 4, 2017 My tuner falls under the 2040:026d I can figure out what it takes to migrate to RC9f if that is my best option to get this working. Link to comment
timl Posted October 5, 2017 Share Posted October 5, 2017 (edited) Ok, so an upgrade to rc9f got things much closer. I now have one adapater being seen and Plex is busy scanning the local channels. However, I am not seeing the second tuner. After reviewing the link you posted above it looks like a kernel patch is required to get the second tuner to be seen. I assume that is not something you are including in this? Edited October 5, 2017 by timl Link to comment
CHBMB Posted October 5, 2017 Share Posted October 5, 2017 Not at the moment, I'm going to wait until V6.4 final release I think as the kernel is likely to get updated again by LT and see where that leads us. Link to comment
mbc0 Posted October 5, 2017 Share Posted October 5, 2017 Hi, I am new to this DVB version and have tried using LIBRELEC 6.3.5 to use my DVBSky V 3.0 S952 (Dual Tuner) As you can see they are both detected but only Tuner 0 works as there is no signal detected on Tuner 1? I have swapped the coax cables over and still only Tuner 0 works. I can confirm that both tuners work in my other system. Any ideas? Link to comment
CHBMB Posted October 5, 2017 Share Posted October 5, 2017 You could try the CrazyCat build or one of the newer release candidates. Link to comment
timl Posted October 5, 2017 Share Posted October 5, 2017 6 hours ago, CHBMB said: Not at the moment, I'm going to wait until V6.4 final release I think as the kernel is likely to get updated again by LT and see where that leads us. Makes sense. Thanks! Link to comment
half Posted October 7, 2017 Share Posted October 7, 2017 (edited) Hi CHBMB, you might rembember that i posted a long time back regarding WinTV DualHD from Hauppauge. I just tryed your https://mirror.linuxserver.io/unraid-dvb-rc/6-4-0-rc9f/rc9f-libreelec.zip to see where things stand with out of the box Dual Tuner support on the DualHD. It was still just one tuner working. So i made two slight changes to your build scripts and rerun them to get proper dualtuner support . This might also help other users with Hauppauge cards. Or maybe you want to test it further, because there are a couple more patches regarding the Hauppauge cards. The GIT repo is from a Hauppauge engineer creating Patches for Ubuntu but they apply fine for kernel 4.12. I also compiled the libreelec modules and using that as my Kernel version. Patchfile attached. Regards and thank you for your awesome support. dualhdsupport.patch Edited October 7, 2017 by half Link to comment
skiman384 Posted October 13, 2017 Share Posted October 13, 2017 (edited) Hey Everyone, Trying to get UnRaid to detect my new USB Hauppauge Dual Tuner Card. https://www.amazon.com/gp/product/B015IL0FIW/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1 I have tried the LibreLec 6.3.5 install, and it won't detect the device. Is there something obvious I am missing? I also installed the 6.4rc9f, and it still was not recognized by the dvb settings page. Rc9f is using Kernal 4.12.x and from what I was reading my tuner should be supported by Kernal 4.11.x. Anyone have any idea on how I can get it to work with Unraid, or should I get a different piece of hardware? Edited October 13, 2017 by skiman384 Link to comment
saarg Posted October 13, 2017 Share Posted October 13, 2017 (edited) 10 hours ago, skiman384 said: Hey Everyone, Trying to get UnRaid to detect my new USB Hauppauge Dual Tuner Card. https://www.amazon.com/gp/product/B015IL0FIW/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1 I have tried the LibreLec 6.3.5 install, and it won't detect the device. Is there something obvious I am missing? I also installed the 6.4rc9f, and it still was not recognized by the dvb settings page. Rc9f is using Kernal 4.12.x and from what I was reading my tuner should be supported by Kernal 4.11.x. Anyone have any idea on how I can get it to work with Unraid, or should I get a different piece of hardware? First thing to do is to identify which build has the drivers for you tuner (if there is). Then if there is a build that supports your tuner and it still doesn't work, provide a screenshot of the dvb plugin page and the syslog. Don't remember for sure, but if it's in the 4.11.x kernel tree, the Libreelec build should support it. Might be the crazycat build supports it also if there is one. But you need the 6.4 builds and only one tuner will show. Edited October 13, 2017 by saarg Link to comment
CHBMB Posted October 13, 2017 Share Posted October 13, 2017 Yeah, I've been having a think about all this and I'm not going to backport anything to v6.3.5 mainly because my build system is all geared up to v6.4 now, and I can't see a final release of v6.4 being that far off..... 1 Link to comment
half Posted October 16, 2017 Share Posted October 16, 2017 On 10/13/2017 at 4:22 AM, skiman384 said: Hey Everyone, Trying to get UnRaid to detect my new USB Hauppauge Dual Tuner Card. https://www.amazon.com/gp/product/B015IL0FIW/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1 I have tried the LibreLec 6.3.5 install, and it won't detect the device. Is there something obvious I am missing? I also installed the 6.4rc9f, and it still was not recognized by the dvb settings page. Rc9f is using Kernal 4.12.x and from what I was reading my tuner should be supported by Kernal 4.11.x. Anyone have any idea on how I can get it to work with Unraid, or should I get a different piece of hardware? With the patches i posted above you can have a working Hauppauge Dual tuner. Either you do it yourself or CHBMB would incorporate them into a seperate branch. None of the mentioned version will support it out of the box. Link to comment
Cessquill Posted October 16, 2017 Share Posted October 16, 2017 Hi - I've just switched to 6.4.0 rc9, and re-run this plugin. I was running the TBS official before, but as that appears to be only for stable, I've switched to the open source version. Since then, TVHeadend doesn't start. I've tried removing and reinstalling, but I get the message... root@localhost:# /usr/local/emhttp/plugins/dynamix.docker.manager/scripts/docker run -d --name="tvheadend" --net="bridge" -e TZ="Europe/London" -e HOST_OS="unRAID" -e "PGID"="100" -e "PUID"="99" -p 9981:9981/tcp -p 9982:9982/tcp -v "/mnt/cache/appdata/tvheadend":"/config":rw -v "/mnt/user/utilities/Incoming/Recordings/":"/recordings":rw --device=/dev/dvb linuxserver/tvheadend 38a90774afa7fc0fa164224f332cfd9d3eb900a2b8ce4a678165f3da0175dfd0 /usr/bin/docker: Error response from daemon: linux runtime spec devices: error gathering device information while adding custom device "/dev/dvb": lstat /dev/dvb: no such file or directory. The command failed. Any ideas? Is it because I've switched drivers? The extra parameters is still in the config. Link to comment
CHBMB Posted October 16, 2017 Share Posted October 16, 2017 What does the Unraid DVB plugin screen show? Link to comment
Cessquill Posted October 16, 2017 Share Posted October 16, 2017 15 minutes ago, CHBMB said: What does the Unraid DVB plugin screen show? Good point - I'll get a screenshot shortly (I'm connected remotely via a mobile at the moment and it'll take a bit of stitching). However I have a TBS 6982 (from memory) with 2 DVB-S inputs, and they're not showing as detected on the DVB plugin page. I'm getting... unRAID Version: 6.4.0-rc9f DVB Version: TBS (Open Source) & LibreELEC ATSC-C, DVB-C, DVB-S(2) & DVB-T(2) Driver Version: 220917 Kernel: Detected Adapter Drivers and Adapters 0-7: Not Detected Link to comment
Cessquill Posted October 16, 2017 Share Posted October 16, 2017 Hi - If I revert back to 6.3.5 TBS Official DVB-S/T I get... Adapter drivers: Detected DVB Adapters 0 & 1: TurboSight TBS 6981 DVBS/S2 front end (apologies, I got my model name wrong, but it would appear that - for me - the Open Source & CrazyCat versions aren't picking up my card) Is there something I'm missing? All I've done is install the LT plugin for allowing pre-release updates and selected a new DVB build. Link to comment
Recommended Posts