allanp81 Posted April 22, 2020 Share Posted April 22, 2020 Just thought I'd chime in and say this worked for me on an old H67 board that refused to POST with any SAS cards in. I was able to get this to boot with 2 H310 SAS cards installed Quote Link to comment
sebg35 Posted April 23, 2020 Share Posted April 23, 2020 Hello, I finally managed to get it working. I had change BIOS mode to Legacy insteed of UEFI.... Now it's working but with poor performance in raid (100Mbs). That's the deal for security i assume 🙂 Thanks for your help Quote Link to comment
bytecaver Posted October 14, 2020 Share Posted October 14, 2020 Wow, after hours of hair-pulling I found this thread & it saved me. Tested & works on an ASUS Sabertooth Z97 Mark 1 board. Quote Link to comment
kolla Posted December 24, 2020 Share Posted December 24, 2020 So glad I found this thread by accident! Solved my issue with DELL H310 & Asus MB I was going to move into.. I almost gave up when I accidently came across this via a google search. Thanks to all! 2 Quote Link to comment
LiLZoo Posted June 24, 2021 Share Posted June 24, 2021 This thread is a lifesaver. The mod worked flawless on a LSI 9207-8i in Gigabyte GA-H81m-DS2V combo. Thanks !!! Quote Link to comment
hamfei Posted August 2, 2021 Share Posted August 2, 2021 It worked for me as well! This is a lifesaver! My SAS2308 worked with PIN 5.6 hacked on a Gigabyte IMB310N board. Quote Link to comment
SOULV1CE Posted October 18, 2021 Share Posted October 18, 2021 This post saved my bacon. Works with my Dell PERC H200 on Gigabyte G1.Sniper 5 motherboard. Quote Link to comment
loz678 Posted December 11, 2021 Share Posted December 11, 2021 on my gigabyte z590 board only one stick of RAM was being detected, the tape trick on the H310 solved it Quote Link to comment
Qwizh Posted December 17, 2021 Share Posted December 17, 2021 Hi guys! I am trying to increase my storage capacity, so I built myself a new server. So, I switched from a PowerEdge R210 II to a selfbuilt server with a Fujitsu d3643-h and an Intel Core i5 8500. It's got two 16GB Crucial 2666 uDIMMs. I tried to move over my Dell Perc H200 (flashed to IT mode) to the new server. But, when booting the server, it hangs on the Fujitsu BIOS splash screen. I tried applying the electrical tape mod, but to no avail. I tried different orientations with the tape, but that didn't help unfortunately. Does anyone know what's wrong or what else could be tried? Thanks a lot in advance! Quote Link to comment
allanp81 Posted December 28, 2021 Share Posted December 28, 2021 do you have any other boot devices attached? I've had issues in the past with devices and option rom. Quote Link to comment
Karl_C Posted July 1, 2022 Share Posted July 1, 2022 Just wanted to add my thanks for this post. Worked a treat Just a bit of tape over those 2 pins did the job, who'd have though it. 1 Quote Link to comment
Lou Posted December 17, 2022 Share Posted December 17, 2022 (edited) Hi I ran into a new problem when upgrading my mother board I removed a super micro mother board x11SAE that ran great with 2 LSI SAS9207-8i cards I replaced the board with another Super Micro board x11SPM-F and installed one LSI card in it and plug the other 2 SAS cable right into the mother board and no matter what setting I tried the board would just loop and not pick up my usb drive nor could I get into the cmos setting until I removed the LSI card, then I could boot up from the USB and once again access the Cmos setting. Does anyone have any idea if there might be a setting I'm missing on this board or is there a compatibility issue. I did try the tape trick with no luck there nice cards not sure why they refuse to work in this board and where plug and play in the other board. Any input would be appreciated. lou Edited December 17, 2022 by Lou Solved Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.