anon0276

Members
  • Posts

    17
  • Joined

  • Last visited

Converted

  • Gender
    Undisclosed

anon0276's Achievements

Noob

Noob (1/14)

0

Reputation

  1. I did not figure this was the problem, but I put in a new gigabit NIC today, and for the last several hours, it has been working just fine.
  2. The part that you quoted was right after I stated that I tested the desktop and got the slow speeds, then I tested the speeds to my laptop, from the desktop, and they were normal. So, desktop to server = crappy. Desktop to laptop = good. Laptop to server = crappy. Laptop to desktop = good.
  3. I stated in the OP that I tested with both the desktop and the laptop. If it were only so easy that it were not the server.
  4. I tested the read/write from two different computers. My laptop wirelessly, and my desktop, connected via ethernet cable.
  5. By try a different client, do you mean something like putty? Tried that, no change. Made the changes to the go file, no change.
  6. UNtil this morning, my UNRAID box was working perfectly. Now I am getting painfully slow read/write speeds. Normally I get around 80 MBps with my desktop(ethernet cable) and 12 MBps with my laptop(wireless N connecting at 150mbps). Today I was having problems deleting some files. The read/write speeds were normal (I am about 95% sure anyway) before I deided to reboot. I stopped sickbeard and sabnzbd, but the array could not unmount the disks. I was telneted in, so I used that to force a reboot. The sickbeard/sabnsbd installs were not via the unmenu package manager, instead I am using the .plg files, managing them under the UNRAID settings. It seems that I need to stop them there, rather than logging in and shutting sab/sick down with thier shutdown options, in order to stop the array. After rebooting, I stopped the parity check that automaticly started, and then deleted the problem files. I tried to back up some files and that is when I got the slow write speeds with my laptop. Writing was about 1.8 MBps, reading was under 500 KBps. I thought maybe stopping the parity check had messed things up, so I rebooted again(after I safely stopped the array). I did not stop the parity check, and I tested the speed again after the parity check finished, and I was getting the same results. I stopped the array, removed the parity drive from the array, started, no change. Stopped array and added parity drive back. I then tested with my desktop. 3MBps write, less than 500k read. I tested read/write to my laptop and speeds were normal. I tested speeds to shares, and to individual drives as well, and there was no change. I did a soft reboot on the router(3 month old linksys E4200) and that resulted in no change. Hard reset on the router, no change. I changed ethernet cables, no change(both cables I used were less than 6 months old and in good condition) I tried all the ethernet ports on the router, and there was no change.Sabnzbd still downloads and transfers the files like usual. Telnet is slow as well - when I type something in, it takes a second or two to catch up. Like it is lagging. My hardware is a ALiveNF6G-DVI motherboard with AMD x2 3800+ cpu, 2g DDR2 RAM, gigabit ethernet, 4x sata2. My drives are a Hitachi 750 GB 7200 RPM cache drive, parity and disk 1 are both WDC_WD20EARS, disk 2 is WDC_WD10EADS. Flash drive is a 8g sandisk. I have seached the forums and found one thread with a smiliar problem, but it was not able to help. I dont think that is is the onboard network card, but I dont know what else it could be. I dont think I can understand the info below about it to know. The disk information looks good to me. I am running UNRAID Server Plus, version 5.0-beta13. Syslog is attached. Thanks in advance. Below is the info from ethtool, ifconfig, and hdparm -tT on all drives, except for the flash drive. root@NAS:~# ethtool eth0 Settings for eth0: Supported ports: [ MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Speed: 1000Mb/s Duplex: Full Port: MII PHYAD: 1 Transceiver: external Auto-negotiation: on Supports Wake-on: g Wake-on: d Link detected: yes root@NAS:~# ifconfig eth0 eth0 Link encap:Ethernet HWaddr 00:13:8f:e7:5f:b2 inet addr:192.168.1.105 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:994933 errors:0 dropped:12 overruns:0 frame:0 TX packets:673245 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1470095892 (1.3 GiB) TX bytes:73254754 (69.8 MiB) Interrupt:43 Base address:0x8000 Disk 1(WDC_WD20EARS) root@NAS:~# hdparm -tT /dev/sda /dev/sda: Timing cached reads: 1444 MB in 2.00 seconds = 722.20 MB/sec Timing buffered disk reads: 328 MB in 3.02 seconds = 108.76 MB/sec Disk 2(WDC_WD10EADS) root@NAS:~# hdparm -tT /dev/sdd /dev/sdd: Timing cached reads: 1470 MB in 2.00 seconds = 735.36 MB/sec Timing buffered disk reads: 296 MB in 3.01 seconds = 98.21 MB/sec Parity (WDC_WD20EARS) root@NAS:~# hdparm -tT /dev/sdc /dev/sdc: Timing cached reads: 1438 MB in 2.00 seconds = 718.62 MB/sec Timing buffered disk reads: 376 MB in 3.02 seconds = 124.45 MB/sec Cache(ST3750528AS) root@NAS:~# hdparm -tT /dev/sde /dev/sde: Timing cached reads: 1400 MB in 2.00 seconds = 700.17 MB/sec Timing buffered disk reads: 302 MB in 3.01 seconds = 100.42 MB/sec root@NAS:~# syslog-2012-01-15.txt
  7. when I tried a static IP, I used dhcp reservation, and changed the info on the flash drive. I rebooted the router, and now I am able to connect to the box i have set up for the server. thanks for the help!
  8. Oh, right. I thought he meant get disk info from terminal. When I boot, it shows tower login: Then i enter 'root' and it goes to root@tower(I think) Yes, I reverted hosts back to normal, and then tried changing it a different way, no joy on either.
  9. I am away from home for work today, so for kicks I hooked my laptop up to the router with a lan cable, and booted up using the same usb drive I have been using at home. And this time I was able to connect to the laptop with the ip address. What sort of hardware could cause things not to work on the other computer?
  10. I missed this part the first time around. I did try pinging tower, and it was good, same results as the ip address. ok, how do I get that info?
  11. terminal in windows shows the label as UNRAID, but I edited it anyway, just in case. still labeled UNRAID.
  12. I formatted the USB using windows 7, and I named the label UNRAID. I have a gparted live cd, maybe I will take a crack at it with that.
  13. Yes, I am aware of that. I figured it would not to any good, but was worth a shot. Also, I am running the latest 5.0 beta. I tried the 4.7 stable, and was not able to get an IP address. I didn't mess with it anymore just went back to the 5.0.
  14. Good idea. I just did it, and was able to ping tower successfully from two computers. Last night I tried something with the hosts file, though I can not remember exactly what, also tried opening up the DMZ for that ip.There is a good chance that I did not not do either of those things right.