DocLove

Hello, I just installed an NetApp DS4246 disk shelf that was connected to an LSI SAS 9200-8e controller with an 40G QSFP SFF-8436 to Mini SAS SFF-8088 DDR Hybrid SAS Cable 4M For NetApp. I then moved my array of 10 SATA hard drives to the array and installed 4 new SSD's into the main server box for new cache pools. I updated the firmware of the LSI SAS 9200-8e to 20.00.07.00. everything was recognized by unraid and I was able to start the array. After I started the array a parity check was started, everything looked good until I was spammed with UDMA CRC ERROR COUNTs from the 10 hard drives in the DS4246. I stopped the parity and moved the 10 hard drives back into the server box and the 6 SSD's into the DS4246. I also reseated all cards and cables. I again started the system and everything was working no more errors. Later that night my system did its app backup and I got a UDMA CRC ERROR COUNT warning on one of the ssd's. so I started googling to see if I could find a solution. the common theme of the UDMA CRC ERROR COUNT problems seems to be connection issues or bad cards. I ordered a new LSI SAS 9207-8e card and it arrived today, I updated the firmware to 20.00.07.00 and replaced the LSI SAS 9200-8e card. I moved 2 of the hard drives from my server box to the DS4246. I started a parity check to see if that had solved my issue, but after a bit the errors came back on the 2 drives on the DS4246. I switched ports on both the LSI card and the DS4246, errors. I swapped the IOM6 modules in the DS4246, still errors, I even removed the bottom IOM6 module to see if there was an issue with the modules. I have ordered a new 2M cable which will be here next week. I have also moved the 2 hard drives back into the server box. does anyone have any suggestions on things I can try/do to fix this issue. if I need to exchange my DS4246 I only have about 2 weeks left. System - Unraid 6.9.2 Motherboard - ASUS KGPE-D16 Processor - 2x AMD Opteron™ 6386 SE Memory - 128gb Network main - Mellanox Technologies MT26448 10g Network Legacy - 4 port gigabit Ethernet Disk Controller 1 - SAS9211-8i Disk Controller 2 - SAS9207-8e paired with an NetApp DS4246 disk shelf Main Array 2 - 8 tb parity. 7 - 8 tb storage. 1 - 4 tb storage. Cache Pools Bulk_File - 2 x 1 tb ssd Cache_docker - 2 x 1 tb ssd Cache_VM - 2 x 1 tb ssd Thanks The Doc. Noticed that there was a lot of "unraid kernel: w83795 1-002f: Failed to read from register 0x045" errors in the log, searched and discovered that this was a sensor error, I removed the "Dynamix System Temp" plugin and they went away. I am pretty sure that this is unrelated to the issue above. unraid-diagnostics-20220318-1616.zip

I have been running Unraid for many years, this popped up and any help would be apricated. unraid-diagnostics-20220218-1900.zip

That got me up and running, thanks for the help. The Doc

@Danuel, if you could let me know how to downgrade that would be great. The Doc

I am having this issue as well, 2019-06-15 06:21:51,020 DEBG 'jackett' stderr output: /home/nobody/start.sh: line 4: 62 Aborted /usr/lib/jackett/jackett --NoRestart --NoUpdates --DataFolder /config/Jackett 2019-06-15 06:21:51,021 DEBG fd 8 closed, stopped monitoring <POutputDispatcher at 23158409793264 for <Subprocess at 23158409793320 with name jackett in state STARTING> (stdout)> 2019-06-15 06:21:51,021 DEBG fd 10 closed, stopped monitoring <POutputDispatcher at 23158409887024 for <Subprocess at 23158409793320 with name jackett in state STARTING> (stderr)> 2019-06-15 06:21:51,021 INFO exited: jackett (exit status 134; not expected) 2019-06-15 06:21:51,022 DEBG received SIGCHLD indicating a child quit 2019-06-15 06:21:54,029 INFO spawned: 'jackett' with pid 67 2019-06-15 06:21:54,138 DEBG 'jackett' stderr output: : Couldn't find a valid ICU package installed on the system. Set the configuration flag System.Globalization.Invariant to true if you want to run with no globalization support. at System.Environment.FailFast(System.String) at System.Globalization.GlobalizationMode.GetGlobalizationInvariantMode() at System.Globalization.GlobalizationMode..cctor() 2019-06-15 06:21:54,138 DEBG 'jackett' stderr output: at System.Globalization.CultureData.CreateCultureWithInvariantData() at System.Globalization.CultureData.get_Invariant() at System.Globalization.CultureInfo..cctor() at System.StringComparer..cctor() at System.AppDomain.InitializeCompatibilityFlags() at System.AppDomain.Setup(System.Object) any idea what happened with the last update?

Thanks for the info, If it continues I will do as you suggest. I hope it was just a one off.

Sh**, just upgraded the CPU's. hope it is just a one time thing, how do I tell which one is having the issue, there are 2 processors on this board.

Hello. I logged into my server today to do something and noticed that Fix common problems was reporting "Machine Check Events detected on your server". I tried to look into the log file, however I am not sure what I am looking for. I have attached the diagnostic zip file, any help in figuring out what is happening would be greatly appreciated. The Doc unraid-diagnostics-20190522-2000.zip

Thank you so much @johnnie.black for your support in working on this problem, do you know when is v6.4 going to be released? the most current stable version is 6.3.5. The Doc

@johnnie.black That did it, every thing runs now, here is what the system returned: 1st command Done, had to relocate 1 out of 4 chunks 2nd command Done, had to relocate 2 out of 4 chunks now the system reports this for cache drive 1 pool information, the drive shows 1% used on the dashboard. Label: none uuid: 7c0a6cb7-b610-4a31-9b58-a09704ac0a81 Total devices 2 FS bytes used 1.17GiB devid 1 size 232.89GiB used 3.03GiB path /dev/sdh1 devid 2 size 232.89GiB used 3.03GiB path /dev/sdg1 is this good? if not what do I do next? Thanks The Doc

@johnnie.black when I try to run the second part of your instructions btrfs balance start -dconvert=raid10 /mnt/cache I get the following ERROR: error during balancing '/mnt/cache': Invalid argument There may be more info in syslog - try dmesg | tail any suggestions? Thanks The Doc.

I got this notification from Fix Common Problems. it told me to: "post your diagnostics and ask for assistance on the unRaid forums" so here I am, what is going on and where the heck should I look for a problem? unraid-diagnostics-20171210-1002.zip Thanks in advance The Doc.

the ports and the admin password were duplicated, removed the dups and everything started fine.

I am getting a failure when installing the mineos-node docker: root@localhost:# /usr/local/emhttp/plugins/dynamix.docker.manager/scripts/docker run -d --name="mineos-node" --net="bridge" -e TZ="America/Los_Angeles" -e HOST_OS="unRAID" -e "USER_PASSWORD"="mypass" -e "USER_PASSWORD"="mypass" -p 25565-25575:25565-25575/tcp -p 8443:8443/tcp -p 25565-25575:25565-25575/tcp -p 8443:8443/tcp -v "/mnt/user/appdata/minecraft/":"/var/games/minecraft":rw -v "/mnt/user/appdata/minecraft/":"/var/games/minecraft":rw -v "/mnt/user":"/unraid":rw hexparrot/mineos:node-jessie Unable to find image 'hexparrot/mineos:node-jessie' locally node-jessie: Pulling from hexparrot/mineos 386a066cd84a: Pulling fs layer acff15b8d24c: Pulling fs layer e5c87c19abf4: Pulling fs layer 38f779cec299: Pulling fs layer 3c20c36229de: Pulling fs layer e0f409cca983: Pulling fs layer afc04af539b4: Pulling fs layer 28709a13ccc7: Pulling fs layer 38f779cec299: Waiting 3c20c36229de: Waiting afc04af539b4: Waiting e0f409cca983: Waiting 28709a13ccc7: Waiting acff15b8d24c: Verifying Checksum acff15b8d24c: Download complete 38f779cec299: Verifying Checksum 38f779cec299: Download complete 3c20c36229de: Verifying Checksum 3c20c36229de: Download complete 386a066cd84a: Verifying Checksum 386a066cd84a: Download complete afc04af539b4: Download complete 28709a13ccc7: Verifying Checksum 28709a13ccc7: Download complete e0f409cca983: Verifying Checksum e0f409cca983: Download complete e5c87c19abf4: Verifying Checksum e5c87c19abf4: Download complete 386a066cd84a: Pull complete 386a066cd84a: Pull complete acff15b8d24c: Pull complete acff15b8d24c: Pull complete e5c87c19abf4: Pull complete e5c87c19abf4: Pull complete 38f779cec299: Pull complete 38f779cec299: Pull complete 3c20c36229de: Pull complete 3c20c36229de: Pull complete e0f409cca983: Pull complete e0f409cca983: Pull complete afc04af539b4: Pull complete afc04af539b4: Pull complete 28709a13ccc7: Pull complete 28709a13ccc7: Pull complete Digest: sha256:6f2664027e16c8ebeb9e1cdf440c32a44fe3560f0a1f9b46e47109bdf2cadaac Status: Downloaded newer image for hexparrot/mineos:node-jessie fdb223d4ae4e1d100d5da08d94b1b803475e4c932b1c424a4de4ba64ffc3d522 docker: Error response from daemon: failed to create endpoint mineos-node on network bridge: Bind for 0.0.0.0:25575 failed: port is already allocated. The command failed. port 25575 is not in use any help would be appricited, I am pulling out what little hair I have left.. The Doc

ah, I even remember reading that somewhere, but the connection wasn't made. Thank you for the quick reply. The Doc.