Trylo

The recent update broke my OnlyOfficeDS. When I try to go to the URL office.mydomain.com I'm getting: 502 Bad Gateway openresty I'm using Nginx Proxy Manager and NextCloud. I noticed that NextCloud informed me that OnlyOfficedS is not available and to check the configuration. The configuration is correct. After clicking save I'm getting: Error when trying to connect (Server error: `GET https://office.mydomain.com/healthcheck` resulted in a `502 Bad Gateway` response: 502 Bad Gateway 502 Bad Gateway open (truncated...) ) I've attached log and nginx error log. Can anyone have a look and help me troubleshoot this? log.txt nginx.error.log

Any plans to enable nvidia GPUs?

Hi! I've got 2 new drives of higher capacity. One to replace the parity drive and one to get some more storage (Seagate Exos X16 ST16000NM001G). Both drives have been put in HDD enclosure that takes 3 drives and it's mounted in 2 5.25" bays. I've always noticed that the drives I had there were running a bit hotter than other drives, but never exceeded 45°C. Also these drives were connected to LSI SAS2008. I've noticed that after maybe 15 minutes pre-read speed dropped from 280MB/s to 66MB/s. I left it for a bit, thinking that it will go back, but after 5h I came back and both were still at around 66MB/s and at 47°C and 49°C! I've stopped the pre-clear and changed the location of the drives. With the location I also changed SATA cables and now those 2 drives are connected via motherboard ports. It's been 1.5h and the speed is around 275MB/s and temp. 38°C. Is this normal that drives slow down when they get hot? Also I read that some people put small fans on the radiator of the LSI SAS2008. I don't have one and it was very hot to touch. Could the LSI SAS2008 also slow down because of high temperature? I've ordered a small 40mm fan for it already. So bottom line is: everything is fine now, but with time as I replace my 2-4TB drives with 16TB drives I want to avoid any mistakes. Any input is welcome! Thank you in advance!

I've updated container today and it looks like Region and Country selection for AirVPN is broken. Gluetun is expecting Upper case first letter, but even if I enter Upper case first letter it somplains that it's a Lower case first letter. So. in configuration I'm entering "Netherlands", but then in log it complains, that "netherlands" is not a valid option and it should be "Netherlands". Same with Europe.

I'm trying to set up OnlyOffice container to work with Nextcloud. I'm using Nginx Proxy Manager. The subdomain is reachable from the internet, but when I enter the address and the secret key I'm getting error: "Error when trying to connect (Error occurred in the document service: Error while downloading the document file to be converted.) (version 7.3.3.49)" Any ideas how to troubleshoot it?

I found this in the documentation (https://networkupstools.org/docs/man/usbhid-ups.html😞 " device = regex Select a UPS on a specific USB device or group of devices. The argument is a regular expression that must match the device name where the UPS is connected (e.g. device="001" or device="00[1-2]") as seen in /proc/bus/usb/devices or lsusb(8); including leading zeroes. Note that device numbers are not guaranteed by the OS to be stable across re-boots or device re-plugging. " My device is: Bus 005 Device 038 Port 5-1 ID 051d:0002 American Power Conversion Uninterruptible Power Supply So I added device="038" to /etc/nut/ups.conf in Config Editor But upon reloading I got this: "Duplicate driver instance detected (PID file /var/run/nut/usbhid-ups-ups.pid exists)! Terminating other driver!" And NUT then reverts back ups.conf to the previous state.

@SimonF so are you saying there is no way to set it up using the plugin?

Good thinking. I'd say it's unlikely. If the PC or Mac is underload for sure not, but if both are ideal it may be close... In this case a RaspberryPi would be safer...

It's a good idea, but wouldn't a lightweight Linux VM make more sense and pass through the USB with the 2nd UPS? I guess this can be my plan B, I'd rather use the NUT plugin.

I have a UPS that I've been using for 6 years, it was handling Unraid machine, Windows PC and a Mac. I've upgraded GPU on my PC machine and the UPS is no longer sufficient, so I bought a bigger one. Now having 2 I'd like first one to handle Unraid and the second one to handle the other 2 computers. Both UPSes and Unraid machine are in one room and the PC and Mac are in the office. I have a power line running from one room to another (I've had it installed while renovating so that I don't have to have annoying UPS sound in the office). Now the question is how to get my main PC shut down in case of power failure. So far I was using the Unraid builtin capabilities to communicate with UPS, but now having 2 I thought that the 2nd one can be connected to the NUT plugin, but when I start NUT it always connects to the first one. How can I select which UPS NUT will connect to? Here is output after clicking "Autodetect": [nutdev1] driver = "usbhid-ups" port = "auto" vendorid = "051D" productid = "0002" product = "Back-UPS XS 1400U FW:926.T1 .I USB FW:T1" serial = "3B1451X16024" vendor = "American Power Conversion" bus = "005" [nutdev2] driver = "usbhid-ups" port = "auto" vendorid = "051D" productid = "0002" product = "Back-UPS BX2200MI FW:378700G -302202G" serial = "9B2221A44604" vendor = "American Power Conversion" bus = "005"

I'm having a problem. I can't get Windows 11 to connect to the USBIP on my Unraid. I'm trying to connect device 5-1. On Unraid side everything looks good: On Windows side I followed this guide: https://sourceforge.net/p/usbip/git-windows/ci/master/tree/trunk/driver/USAGE but I'm getting errors: C:\Users\andrz\Downloads>usbip -l 192.168.2.5 - 192.168.2.5 usbip err: usbip_network.c: 121 (usbip_recv_op_common) recv op_common, -1 usbip err: usbip.c: 216 (query_exported_devices) recv op_common usbip err: usbip.c: 288 (show_exported_devices) query Am I doing something wrong?

Wow! The test probably failed between me starting it and exporting the diagnostics. Thank you for quick help.

Hi! This morning I woke up to a message "array has 1 disk with read errors" Disk 5 had 1850 erorrs. I did open the case yesterday, I didn't touch drives, but I shut the machine down and made sure that all sata cables are sitting in properly. Booted up unraid and started parity check, quickly I got the same message again. I'm posting here the diagnostics. I've also started extended SMART self-test, but as it take ages - maybe someone can tell me based on diagonstics if I should just order a new drive. Thank you! nas-diagnostics-20230322-1110.zip

I've got it 5 minutes after I posted it Thank you for the quick reply!

I've checked. The CPU Fan is PWM and bios is set to PWM.