miniwalks

Members
  • Content count

    57
  • Joined

  • Last visited

Community Reputation

5 Neutral

About miniwalks

  • Rank
    Advanced Member

Converted

  • Gender
    Undisclosed
  1. Hopefully I'll have some time to play around with this later today/this week, as I have 9 cameras that would need to be tested/migrated Sent from my iPhone using Tapatalk
  2. Sorry I fell asleep during posting it on my phone Crossflashing takes 15-20minutes and is quite well documented Sent from my iPhone using Tapatalk
  3. That would be for minor bug fixes etc. The 2TB drive size limit is due to the 64bit LBA boundary and is a hardware restriction in the card, which cannot be solved with a firmware update. Like Jonnie I strongly recommend the LSI2008 based cards he listed, as they are cheap and come in configurations that suit the server and case layout you may require. Crossflashing takes Sent from my iPhone using Tapatalk
  4. I'm guessing you don't use the Docker/VM Engine on those cacheless servers? Sent from my iPhone using Tapatalk
  5. Most welcome Dennis, hopefully that gets you back going again I have those nights every few months or so that I'll go clean out old crap that I can't recognise anymore. Generally gets done when I do update sweeps that aren't automated Sent from my iPhone using Tapatalk
  6. My cache is underpinned by 2 500GB SSD's in a hardware raid, as I had bad experiences with BTRFS. The idea is that I can deal with the cost of the SSD for the trade off that my transcoding and post scripts that occur are occurring all in flash, and that the shows etc that I want to watch are immediately available on always spun up cache drive. This in turn gives me a power saving as to not have to constant spin up a myriad of drives to complete a tiny task. I prefer my redundancy everywhere. And I also keep backups of everything important on a separate array and offsite. That being said, when I migrated my production data to Unraid I used rsync to the user0 share as to avoid the cache disk. Simpler method if you ask me Sent from my iPhone using Tapatalk
  7. tried again with 6.3.3, the mtip32xx driver exists, however its unable to detect the drive correctly I have loaded Microns RealSSD Manager (RSSDM) which gives the below: root@Tower:~# rssdm -L DiscoverDrives operation failed CMD_STATUS : Unable to find any P320/P420 drives connected STATUS_CODE : 10 Copyright (C) 2014 Micron Technology, Inc. root@Tower:~# lspci -v 02:00.0 Mass storage controller: Micron Technology Inc RealSSD P320h (rev 03) Subsystem: Micron Technology Inc RealSSD P320h Flags: bus master, fast devsel, latency 0, IRQ 28 Memory at f7c07000 (32-bit, non-prefetchable) Memory at f7c06000 (32-bit, non-prefetchable) I/O ports at e000 Memory at f7c04000 (32-bit, non-prefetchable) Expansion ROM at f7c00000 [disabled] Capabilities: [40] Express Endpoint, MSI 00 Capabilities: [c0] Power Management version 3 Capabilities: [d0] MSI: Enable+ Count=1/8 Maskable+ 64bit+ Capabilities: [100] Advanced Error Reporting Kernel driver in use: mtip32xx Kernel modules: mtip32xx
  8. Fwiw some plugins can fall out of sync and stop detecting as out of date. I had the issue myself with the preclear plugin. I've noticed it happen twice with plugins which didn't update correctly were manually URL added ones rather than via CA Perhaps you could try removing some plugins and re-adding them via CA? Re SAMBA, there were some significant changes, some users noticing that some changes were needing in the SMB config to work correctly. Not sure if that helps you or not though Sent from my iPhone using Tapatalk
  9. Hell, I only run my mover once a week The upside of using 500gb SSDs in cache I guess. Sent from my iPhone using Tapatalk
  10. Thanks for that, I'm guessing there's no WebUI for the software? And that you have to use an app to configure the software? Sent from my iPhone using Tapatalk
  11. Running into some issues: *** Running /etc/my_init.d/00_regen_ssh_host_keys.sh...*** Running /etc/my_init.d/50_configure_xeoma.sh...*** Running /etc/rc.local...*** Booting runit daemon...*** Runit started as PID 21[Apr 23 01:13:05 AM] Using the stable version of Xeoma[Apr 23 01:13:05 AM] Setting the passwordApr 23 01:13:05 0cbbfe9f9198 syslog-ng[28]: syslog-ng starting up; version='3.5.6'Failed to open 'libX11'Password set successfull[Apr 23 01:13:05 AM] Starting the server in 5 seconds... ^^^ This never starts
  12. I was thinking that too, hence no need to load everything into the kernel of unraid, should just pass it through to a VM/Docker instead Sent from my iPhone using Tapatalk
  13. Out of interest, what is your purpose for the card? Like is it for a Docker or VM? Sent from my iPhone using Tapatalk
  14. i have this same issue on a test box, it seems that atleast in 6.3.2 (going to try 6.3.3 again soon) that the mtip32xx.ko isnt in /lib/modules/4.9.10-unRAID/kernel/drivers/block/mtip32xx/ Hopefully someone from Limetech can help?
  15. I'll keep digging into this one, the issue may be with the controller not mounting the disk behind it. I'll have a look into loading up the micron utilities on the server to play with it Sent from my iPhone using Tapatalk
Copyright © 2005-2017 Lime Technology, Inc. unRAIDĀ® is a registered trademark of Lime Technology, Inc.