Heffa

Members
  • Content count

    25
  • Joined

  • Last visited

Community Reputation

0 Neutral

About Heffa

  • Rank
    Member

Converted

  • Gender
    Undisclosed
  1. Thanks for the fan control! I can now run a parity check without worrying about temperatures.
  2. ASRock - E3C226D2I
  3. Any update on being able to control fans from the plugin?
  4. My old server was five years old and started getting hard drive warnings, rather than replace the drives I figured I'd go for a completely new build. I wanted to keep the new build small as the old one fits in my IKEA unit under the TV. After looking at a couple of cases I went for the Silverstone DS380 as I liked the hot swap bays and it would fit. I was aware of a design flaw inherent in the case but there is an easy work around as you'll see below. I've written this up all in one go so the issues I mention in the updates have already been resolved. Here are the specs: OS at time of building: 6.3.1 CPU: Intel® Xeon® CPU E3-1231 v3 @ 3.40GHz Motherboard: ASRock - E3C226D2I RAM: 16GB (2x 8GB) Crucial Server Memory, DDR3 PC3-12800 ECC Case: Silverstone DS380 Drive Cage(s): Built in 8 bay hot swap Power Supply: 300W Silverstone ST30SF Strider SFX SATA Expansion Card(s): None Cables: 15cm Akasa Super Slim SATA III, Akasa PWM fan splitter Fans: 120mm Noctua NF-S12B REDUX PWM x 3 Parity Drive: 4TB WD Red Data Drives: 4TB WD Red x 3 Cache Drive: 120GB Kingston SSD Now V300 Total Drive Capacity: 8 x 3.5", 4 x 2.5" Primary Use: Plex Media Server, backup storage Likes: Very quiet, cool, low power usage Dislikes: Cooling design flaw Add Ons Used: Plex Media Server, pre_clear plugin, unassigned devices Future Plans: More dockers, Time Machine backup Boot (peak): 98W Idle (avg): 30W Active (avg): 47W Light use (avg): 35W Update 1 The build went smoothly, although the case is tricky to work with. It's very small and there is no room for any cable management. If you ever use the same case be sure to read the manual as it well tell you the best order to install components in. I'm using a SanDisk Fit USB plugged into a front usb port, its small enough to allow the door to be closed. I ordered short (15cm) thin SATA cables hoping to cut down on excessive cables however they were just a bit too short and I was only able to connect 4/6 ports, 25cm cables would have been perfect. The PSU is great as the fan only spins up when its under heavy load which so far is never. The motherboard does not have enough fan headers for all three fans but the hard drive caddy has two headers on it. Unfortunately this means the fans run at full speed all the time. The USB3 cables from the front header are annoyingly inflexible and long, curling them up was the best way to deal with them. The Design Flaw There is a known problem with this case; due to the design of the hard drive bay the to fans adjacent two it provide insufficient cooling. Idle temperatures for drives hover around 32C and during parity check one reached 46C! The issue is that there is little space for air to flow through to the drives (you can see the slots in the third picture), this only gets worse the more drives you use. To fix this you need to prevent the air from flowing anywhere but through the slots. I cut a piece of cardboard and slotted it between the two fans and the metal that raises the motherboard. Doing this results in over a 10C drop in temperatures. Checking parity again maxed out at 33C, a huge improvement. Update 2 Ordered three Noctua fans, another hard drive, and a fan splitter. Now all the fans are hooked up to the motherboard the case is almost inaudible.
  5. Thanks for the help! I'll get a second RAM stick and keep the SSD as its been adequate for my needs.
  6. Thought I'd have some fun and build a new server rather than upgrade my old one. My needs are to store blu-ray rips, stream Plex to 1-2 devices (3 max), accessible from anywhere, sleep after inactivity, wake-on-lan, low power consumption. It's been five years since my last build and I would like this one to be as future proof. Build CPU: Intel Xeon E3-1231 V3 Motherboard: AsRock E3C226D2I mini-ITX Xeon Socket 1150 RAM: 8GB (1x 8GB) Crucial Server Memory, DDR3 PC3-12800 (1600), ECC, Unbuffered Case: Silverstone SST-DS380B Power Supply: 300W Silverstone ST30SF Strider SFX Parity Drive: Western Digital 4TB Red x1 Data Drives: Western Digital 4TB Red x2 Cache Drive: Crucial 64GB Real SSD C300 (from an old build) USB: SanDisk Cruzer Fit 16GB USB 2.0 Questions Everything look ok? Is the CPU overpowered for my needs, can I get away with a cheaper one? Is one RAM stick ok or is it better to have two? Is it worth buying a new SSD for use as a cache drive? Will there be a noticeable performance improvement? Thanks for the help!
  7. The slot is empty so I could get a SATA controller. I completely forgot to mention that I would buy new HDDs to replace the failing one(s) which ever option I go for. I appreciate your suggestion, I had almost completely ruled out 1 but now I'm having second thoughts. The case is fine except that it has no room for expansion and the airflow is not great. If I were to go for a new build what CPU/MB/RAM is recommended given my usage?
  8. My build is getting on five years old now and its time for an upgrade. My parity drive is throwing a bunch of SMART warnings and rather than just replace the drive I figured I'd build a new system while trying to use as many parts from the old as I could. It primarily acts as a Plex Server with one client (three at the most). This is the current system: Case: Lian Li PC-Q08B Motherboard: Zotac H55ITX-A-E CPU: Intel Core i3 530 Memory: 4GB (2x2GB) Corsair XMS3 DDR3 unRAID Drive: SanDisk Cruzer Micro 8GB Cache: SSD Crucial C300 64GB Storage: Western Digital Caviar Green 1.5TB (WD15EADS) x 3 (1 Parity) Western Digital Caviar Green 1.5TB (WD15EARS) x 2 The case has been great but I'm looking to upgrade to one with more room for drives, I'm thinking the Fractal Design Node 804. This would also give me the ability to use a micro-ATX board. These are the options I see: 1. Keep the CPU/MB/RAM the same, get a card to provide more SATA ports 2. Keep the CPU but upgrade the MB (and RAM?) to provide more SATA ports 3. New CPU/MB/RAM If my CPU is still adequate I'd like to go for option two in which case what MB should I go for? Additionally if I could make my system more energy efficient with option three what CPU/MB/RAM combo should I go for? Many thanks
  9. Could I request a PlexConnect plugin? Thanks for all the other plugins! https://github.com/iBaa/PlexConnect Currently using this version http://lime-technology.com/forum/index.php?topic=29193.0
  10. Thanks for your help setting this up, I am having issues with it though. Everything works fine but only if I start by using python PlexConnect.py. I have tried running the nohup command both on OS X in terminal and using puTTy on windows. Either way I get the message 'nohup: ignoring input and appending output to `nohup.out'', the AppleTV will keep trying to access trailers until I press the menu button. I have little experience with running console commands but it seems like plexconnect isn't starting, do you have any suggestions on what to do?
  11. You don't need to but I would recommend it. I was running the apps on a hard drive in the array but that meant that the disk was always spun up which is not good for energy usage. I used an old 64GB SSD I had for the cache drive and its much better. As for using the usb flash drive my understanding is that the apps are downloaded to the drive when you first run the script to install them and then they are copied to the RAM (I may be completely wrong) when they are running. I am not sure about saving the app data directories to the usb drive, I remember reading that it is not recommended due to the number of read/writes the drive will be put through.
  12. You may find it easier to upgrade to 5beta14 and use the plugin install system. All you have to do is put the plg files on the flash drive and next time you reboot Sabnzbd, Sickbeard ect will be installed. Then all you have to do is specify the data directories through the web interface and enable the plugins.
  13. I hope this isn't against the rules but I have an unused GD04 that I could sell you at a bargain price (hopefully you live in the UK). Great design btw.
  14. I've got the same issue, there is a large thread in the Sickbeard support forum about this problem. The temporary fix is to restart sick beard however this only works for a few hours/one day. You can restart sick beard by clicking the top left icon and selecting restart from the drop down menu, hope this helps.
  15. Sorry I hadn't checked the syslog. I just looked at the speed at the start of the sync before letting it run over night.
Copyright © 2005-2017 Lime Technology, Inc. unRAID® is a registered trademark of Lime Technology, Inc.